Banner Ad 1

about lathes - get one and have a look at these sites

Post your favorite modeling 'tips' and 'tricks'

Postby raalst » Wed Mar 05, 2003 5:13 pm

Hi all,
advance your general tinkering capabilities with a lathe !
in the US small lathes seem to sell for about $400
(in europe it costed me 700 euro..)

If you consider this (a hobby of it's own), have a look at

yahoo minilathe group (also check related groups : somebody
is scanning an publishing lots of old material on "model engineering".
it contains a wealth of how-to info on lathes and related
skills like drilling etc.)

and
www.mini-lathe.com
this is the definitive site for that type of minilathe but it's
links and lots of info is of a more general type

These are just starting points for your exploration.
They took me a while to find, so I decided to put them
up here.

I really like the capabilities these lathes bring into reach :
- selfmade hydraulics and valves
- sturdy parts and accessories (like brass periscopes)
- selfmade gears and bolts
- selfmade piston tanks
- selfmade compressors
and everything I have not thought of until today

have yourself yet another hobby

Regards,
Ronald van Aalst
Regards,

Ronald van Aalst

--------------------------------------------
Just here to Learn
User avatar
raalst
SubCommittee Member
 
Posts: 1319
Joined: Wed Feb 26, 2003 8:46 am
Location: netherlands, the hague

Postby Tom Spettel » Wed Mar 05, 2003 10:50 pm

Yes they are very nice.. I have the Sherline mill with digital read out. sher line has a very nice line of machines as well parts and tooling.
I also have a taig lathe. its nice..
i would call it a beginer lathe, Taig
also has is good for parts but dosent
have as much tooling to offer.
Tom
A list and a plunge and down she goes to Davy Jones.
Raiders of the Deep
User avatar
Tom Spettel
Registered User
 
Posts: 94
Joined: Sat Feb 22, 2003 2:46 am

Postby Britt Boyette » Thu Mar 06, 2003 11:12 am

Maybe Tom, but a Taig sure beats the #### out of a hand drill mounted in a vice. Been there, done that.
Britt Boyette

Break Like The Wind Racing
Britt Boyette
Registered User
 
Posts: 127
Joined: Sat Feb 22, 2003 12:44 am
Location: Keizer, OR

Postby Bigdave » Fri Mar 07, 2003 9:48 am

I had a taig it was a nice little lathe. I now have a bigger G4000 Grizzly 9x20 lathe. I have have had a few problems with it. The quality on the asian machines is not as good as the ones made here. But alot cheeper. My best friend has a Sherline lathe and mill. They are strictly for small stuff but they are excellent machines. Alot better than my taig was. I would check E-bay and other places and look for a used Sherline if I was going to do it again. The smaller Grizzly Mini lathe (also sold by others) has a large following on the Net. Search the web, I found alot of info on fixes for the problems for my lathe up there. It now cuts alot better. I also have the Grizzly mini mill G8689. It is a great machine. I find I use the mill much more than the lathe anyway. Join the fun and (Throw some chip's) Good Luck.



Edited By Bigdave on 1047045071
David Welch
Commodore SR-8

Image


"Eat your pudding Mr Land". "I ain't sure it's puddin" James Mason-Kirk
Douglas, 20K
User avatar
Bigdave
SubCommittee Member
 
Posts: 2861
Joined: Fri Feb 21, 2003 8:33 am
Location: Rochester NY


Return to Modeling Tips and Tricks

Who is online

Users browsing this forum: No registered users

cron